出Error: Connect failed, Exit Meta Mode and turn to next phone.的请进

lonergb

出Error: Connect failed, Exit Meta Mode and turn to next phone.的请进










线刷机时因为手贱，点了FORMAT后，结果就出8038错误，后来弄到半夜终于刷成功了，但MAC和IMEI已经丢失。用了几天后发现并不太影响使用，但看着很不爽。研究了半个多月，电脑重装N次， 两台电脑来回折腾终于把MAC和IMEI恢复了。
具体教程可以开GOOGLE搜索“恢复IMEI”

网上恢复MAC和IMEI的教程很多，但我照他们的方法做不成功，具体就是在插入USB线后提示
Error: Connect failed, Exit Meta Mode and turn to next phone.

之前的信息是：
>>Step: Start to Connect with target.
COM port searching and preloader handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
    Error: Connect failed, Exit Meta Mode and turn to next phone.

开始以为是驱动不对，弄了很久，也没结果。经过半个月的折腾终于弄清楚，MODEM Database和AP Database文件必须从原版相同版本的线刷包中提取，否则会出错。

例如，我的机现在的ROM版本为S510_131122,那么，这个软件中的所选的MODEM Database和AP Database文件就必须从S510_131122版本的刷机包中提取，不能用别的文件！



现阶段网上所有的教程，没有一个提到版本问题，最多就是提供这两个文件的下载连接。

卡刷包本人没有试过， 为了保险还是先刷原厂线刷包，完了再用这个线刷包里的MODEM Database和AP Database文件。


下面是刷机正常时的提示信息：
(1)IMEI部分
>>Step: Enter func_imei_meta_hdlr_smart_phone_modem();
        Write IMEI to smartphone modem nvram
>>Step: Start to Init Modem Nvram Database...
   OK: Init Modem Nvram Database successfully.

>>---------------------------------------------------<<
    OK: IMEI[0] = "8600XXXXXXXXXXX".


>>Step: Start to Connect with target.
COM port searching and preloader handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
   OK: Connect successfully.
>>Step: To get SVN and PAD from phone.
   OK: SVN=0xff and PAD=0xff
>>Step: Start to write. CheckSum=1, IMEILock=0.
   OK: Write IMEI successfully.
   OK: Check IMEI. Rd_imei = "8600XXXXXXXXXXX".
    OK: IMEI[1] = "8600XXXXXXXXXXX".
>>Step: To get SVN and PAD from phone.
   OK: SVN=0xff and PAD=0xff
>>Step: Start to write. CheckSum=1, IMEILock=0.
   OK: Write IMEI successfully.
   OK: Check IMEI. Rd_imei = "8600XXXXXXXXXXX".
>> Step: To switch Meta to AP side...
    OK: META_DisconnectInMe**ode_r()
    OK: Switch2WM_META_Mode()
>>Step: To Backup NVRAM to Bin Region, and Set Clean Boot Flag
    OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize()
>> Step: Meta Disconnect with target.

>>---------------------------------------------------<<
>>Step: Cancel scan IMEI DiagBox.


（2）MAC部分

>> Step: To switch Meta to AP side...
    OK: META_DisconnectInMe**ode_r()
    OK: Switch2WM_META_Mode()

>>Step: To Backup NVRAM to Bin Region, and Set Clean Boot Flag
    OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize()

>> Step: Meta Disconnect with target.

>>---------------------------------------------------<<
>>Step: Cancel scan IMEI DiagBox.
>>-------------------------------------------------------------------<<
>>Step: Enter func_wifi_mac_meta_hdlr_smart_phone_Ex();
        Write Wifi MAC  to smart phone nvram
>>Step: Start to Init smart phone Database...
   OK: Init AP Nvram Database successfully.


>>-------------------------------------------------------------<<
>>Step: Scan Smart Phone Wifi MAC.
    OK: Wifi MAC = "XXXXXXXXXXX".
>>Step: Start to Connect with target.
COM port searching and preloader handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
COM port searching and Kernel handshake OK
    OK: Connect to target successfully.
>>Step: Start to write Wifi MAC.
    OK: Write Wifi MACsuccessfully.
>>Step: Start to check Wifi MAC.
    OK: Check Wifi MAC Pass. Wifi MAC = "xxxxxxxxxxxx".

>>Step: To Backup NVRAM to Bin Region, and Set Clean Boot Flag
    OK: Backup NVRAM and WM_META_SetCleanBootFlag_Customize()
>>Step: Meta Disconnect with target.

>>-------------------------------------------------------------<<
>>Step: Scan Smart Phone Wifi MAC.
>>Step: Cancel scan Address DiagBox.




下面是本人不成功时的提示信息：
>>Step: Start to Connect with target.
COM port searching and preloader handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
    Error: Connect failed, Exit Meta Mode and turn to next phone.



下面是刷MAC和IMEI时用到的软件以及驱动：
http://pan.baidu.com/share/link?shareid=1236522917&uk=1748775493